How to Reset a Frigidaire Refrigerator or Freezer

Unplug 30 seconds to clear codes Demo 77 77: unplug 5 minutes Sabbath: hold 5 seconds Reset fixes settings, not parts

Quick Answer: How to Reset a Frigidaire Refrigerator

Frigidaire’s own reset is a power cycle: unplug the refrigerator for 30 seconds and plug it back in. If you cannot reach the plug, Frigidaire says you can switch off the breaker instead, noting that this resets everything else on the same circuit.

  • Alarms: press CLEAR ALERTS (or Alarm Reset on older models) to acknowledge door, high-temperature and power-outage alarms
  • Demo mode, shown as 77 77: Frigidaire says to unplug the unit for 5 minutes and plug it back in
  • Sabbath mode, shown as Sb: hold two buttons together for 5 seconds; which two depends on the model
  • Control lock and filter status: usually a 3-second hold on the matching button
  • Codes Er CE or Er T1 to Er T6: Frigidaire says these can mean authorized service is required

A reset is worth doing, and Frigidaire tells owners how. But it is worth being clear about what it does: a power cycle clears a control’s confusion, an alarm reset acknowledges an event, and a mode reset turns off a setting. None of them repairs a part. This page sets out each Frigidaire reset as Frigidaire describes it, for refrigerators including the Gallery range and for upright and chest freezers, and then says what it means if the problem comes straight back.

Reset done, problem back?

If the fridge or freezer returns to the same fault after a reset, tell us the model number and the code on the display. The $99 diagnostic is applied to the repair when you approve it.

The Power Reset: Unplug for 30 Seconds

Frigidaire’s refrigerator error code guide gives the reset in plain terms: reset the unit by unplugging it for 30 seconds and plugging it back in. If you cannot reach the plug, you can switch the breaker off at the fuse box, and Frigidaire notes this resets everything on the same circuit. For a display that is beeping and lighting up unexpectedly, the same guide suggests a hard reset by unplugging for 2 to 3 minutes.

After a reset, give the refrigerator time before judging it. Frigidaire’s troubleshooting repeatedly asks for 24 hours after any change to the controls for the temperature to stabilize. A fridge that is still warm an hour after a reset has not failed the reset; it has not had time.

Clear Alerts: Door, High Temperature and Power Outage

Many Frigidaire “faults” are alarms doing their job. Frigidaire’s guides describe them:

Common Frigidaire refrigerator alarms and how Frigidaire says to clear them
DisplayWhat Frigidaire says it meansHow to clear it
Door AjarA door has been left open for over 5 minutesClose the door; press CLEAR ALERTS
H or HI, High TempThe temperature has been too high in the refrigerator or freezer for over one hourPress CLEAR ALERTS to acknowledge; the alarm repeats every 60 seconds until you do
PF, Power FailureThere has been a power outagePress CLEAR ALERTS, or Alarm Reset on older models, then check the food
Freezer or fridge temperature alarm (four-door models)Freezer at 26°F or warmer, or refrigerator at 55°F or warmerPress Set or Alarm Reset once the cause is fixed

On Gallery models such as the GRFC2353AF and GRMG2272CF, the CLEAR ALERTS button resets any active door open, high temperature and power outage alarm. A high-temperature alarm that keeps coming back after the door is shut and the food is not warm is no longer an alarm problem: it is the refrigerator not holding temperature, which is covered in Frigidaire refrigerator not cooling.

Demo Mode: The Reset That Restores Cooling

This is the reset that matters most, because demo mode turns the cooling off on purpose. Frigidaire describes it as a mode designed for display in a store without using the functional components. How to clear it depends on what the display shows:

  • 77 77 on the display: Frigidaire’s error code guide says to unplug the unit for 5 minutes and plug it back in, which disables demo mode
  • DEMO on the display, Frigidaire Professional all-refrigerator (FPRU19F8WF): the manual says cooling has stopped, and to exit, press and hold the minus button and WATER FILTER together for 10 seconds
  • DEMO on the display, Frigidaire Professional upright freezer (FPFU19F8WF): press and hold the minus button and ICE MAKER together for 10 seconds

A refrigerator that arrived new and never got cold, with the lights and display working normally, is the classic demo-mode case.

Sabbath Mode, Shown as Sb

Sabbath mode changes how the display, lights and alarms behave, and Frigidaire says the display shows Sb while it is on. It is turned on and off by holding two buttons together for 5 seconds, and the pair depends on the model:

  • Gallery French door (GRMG2272CF, GRFC2353AF) and others: minus and Temp F-C
  • Gallery side by side (GRSS2652AF): minus on the freezer side and plus on the refrigerator side
  • Other models: Frigidaire’s support page lists the down arrow and plus, or the freezer minus and the refrigerator plus

One detail catches people out. Frigidaire’s GRMG2272CF manual says the refrigerator stays in Sabbath mode after a power failure, so unplugging it does not clear Sb: it has to be turned off with the buttons on the display.

Control Lock, Filter Status and Factory Defaults

Three more resets on Frigidaire panels, each a hold of about 3 seconds on the models we checked:

  • Control lock: press and hold the lock button for 3 seconds to enable or disable it. On the Gallery side-by-side, Frigidaire notes that dispensing ice and water is disabled while the display is locked, which is easily mistaken for a dispenser fault
  • Water filter status: after fitting a new filter, press and hold Water Filter for 3 seconds to reset the status to GOOD; on some French-door models with a genuine filter, Frigidaire says the alert clears on its own after 30 seconds
  • Factory defaults: on Gallery models with a Default Settings button, press and hold it for 3 seconds to reset to factory settings

How to Reset a Frigidaire Freezer

Frigidaire upright and chest freezers reset differently from refrigerators, and many have no display at all.

  • Upright freezers with an electronic control (FPFU19F8WF): reset a power outage alarm by pressing POWER OUTAGE, and a high temperature alarm by pressing HIGH TEMP. Freeze Boost runs for up to 24 hours and can be turned off by pressing it again
  • Upright freezers with outside controls: Frigidaire’s manual says to reset the high temperature and power failure alarms by pressing and holding the Temp button for 3 seconds
  • Upright freezers with the knob inside: the high temperature alert is reset by opening and then closing the door
  • Chest freezers: on the model we checked, there is no alarm to reset; the green Power On light shows it is connected, even with the control turned to OFF

After a freezer has been off, Frigidaire’s manuals ask for patience: allow 4 hours for it to cool down completely before loading unfrozen food, and 24 hours for the temperature to stabilize between adjustments. If a chest freezer will not run at all, Frigidaire’s troubleshooting points at a ground fault interrupt circuit and says to use another circuit.

When a Reset Is Not Enough

Frigidaire is direct about this: if you see Er CE or Er T1 through Er T6, it says authorized service may be required. More generally, a reset that fixes the problem for a day or a week and then needs doing again is telling you something. A defrost fault, for example, is often hidden for days by switching the machine off, because the ice on the evaporator melts while it is unplugged and then regrows. The same pattern is set out for another make in how to reset an LG refrigerator.

What our own records say about the repair once the reset runs out: across 247 completed refrigeration repairs, the median finished repair is $375, the middle half runs $250 to $462, and Frigidaire appears on 23 of our completed repairs across all appliance types with a median bill of $325. The exact price is given after the $99 diagnostic, which comes off the repair when you approve it. Refrigerator work in general is on the refrigerator repair page.

Frequently Asked Questions

How do I reset my Frigidaire refrigerator?
Unplug it for 30 seconds and plug it back in; that is the reset Frigidaire’s error code guide gives. If you cannot reach the plug, switch the breaker off at the fuse box instead, which also resets everything else on that circuit. For a display that is beeping and lighting up unexpectedly, Frigidaire suggests unplugging for 2 to 3 minutes. Allow 24 hours afterwards for the temperature to stabilize.
How do I reset a Frigidaire Gallery refrigerator?
The power reset is the same: unplug for 30 seconds. On Gallery models, CLEAR ALERTS resets active door, high-temperature and power-outage alarms, holding Water Filter for 3 seconds resets the filter status, and on models with a Default Settings button, holding it for 3 seconds resets to factory settings. Sabbath mode is turned off by holding two buttons together for 5 seconds, minus and Temp F-C on the Gallery French-door models we checked.
How do I get my Frigidaire out of demo mode?
If the display shows 77 77, Frigidaire says to unplug the unit for 5 minutes and plug it back in. On the Frigidaire Professional all-refrigerator that shows DEMO, the manual says to hold the minus button and WATER FILTER together for 10 seconds; on the Professional upright freezer, minus and ICE MAKER for 10 seconds. Demo mode stops the cooling while the lights work, so a new fridge that never got cold is the usual sign.
What does Sb mean on a Frigidaire refrigerator?
Sb means Sabbath mode is on. Frigidaire says it is turned on and off by holding two buttons together for 5 seconds; depending on the model, minus and Temp F-C, the down arrow and plus, or the freezer minus and the refrigerator plus. On at least one Gallery model, the fridge stays in Sabbath mode after a power failure, so it has to be turned off at the display.
How do I reset a Frigidaire freezer?
It depends on the model. On upright freezers with an electronic control, press POWER OUTAGE or HIGH TEMP to reset those alarms. On models with outside controls, Frigidaire says to hold the Temp button for 3 seconds. On models with the knob inside, opening and closing the door resets the high temperature alert. The chest freezer we checked has no alarm to reset. After any power-off, allow 4 hours before loading unfrozen food.
Why does my Frigidaire keep needing a reset?
Because a reset clears the control, not the cause. If the same alarm or code returns, the fault is still there; a defrost problem, for example, can be hidden for days by switching the machine off while the ice melts. Frigidaire says that codes Er CE and Er T1 to Er T6 can mean authorized service is required.

Sources: the power reset, unplug times, alarm meanings, demo mode 77 77, Sabbath mode and the Er CE and Er T codes are from Frigidaire’s owner support pages for refrigerator error codes and alarms, Sabbath mode and high temperature alarms. Demo exits, control lock, filter reset, default settings and freezer resets are from Frigidaire Use and Care manuals A16366506 (FPRU19F8WF), A16366305 (FPFU19F8WF), A17856403 (GRFC2353AF), A22186602 (GRMG2272CF), A19894605 (GRSS2652AF), A23689603, A12735807, A24313002 and A10092403. Repair figures are Neighborville’s own completed jobs, February 2024 to September 2026, counted as jobs billed above the diagnostic fee with tax, above $108.90. Neighborville is an independent repair company and is not affiliated with Frigidaire or Electrolux; brand names are used to identify the appliances we service.

Last updated: November 2026.

Reset once, then watch it.

If the same code or the same warm cabinet comes back, the reset has done its job by showing you the fault is real. Tell us the code and the model number.

Book online Call us