Why Is My Washer Shaking Violently? Causes and Fixes

Shipping bolts first on a new front loader Up to 1/4 inch of movement can be normal Level, load, floor, then parts Median washer repair $352

Quick Answer: Why Is My Washer Shaking Violently?

A washer that shakes violently on spin is usually unbalanced, not level, or still has its shipping bolts in. Whirlpool, Samsung and GE all put those checks first. If the machine is level, the load is spread and it still bangs, the suspension, the counterweights or the drum bearings are next.

  • New front loader? Whirlpool says the shipping bolts must come out after installation, and Samsung says a washer with them in will shake a lot
  • Leveling: all four feet firm on the floor, and GE says the shorter the legs, the steadier the washer
  • The load: one bath mat or a bunched duvet can throw the drum off balance
  • The floor: a weak, uneven or slippery floor makes a level washer move
  • Median washer repair in Neighborville’s own book: $352, middle half $257 to $416

Some movement during spin is normal. GE says a washer moving up to a quarter of an inch now and then can be fine, because the machine is designed to move rather than pass every force into the floor. Violent shaking, banging, or a washer that walks across the room is something else. Below are the checks in the order manufacturers give them, what it means when they all pass, and when to stop using the machine.

Still banging after leveling?

If the washer is level, the load is spread and it still shakes, tell us whether it is a top loader or a front loader. The $99 diagnostic is applied to the repair when you approve it.

When Does Your Washer Shake? That Tells You Most of the Answer

The moment the shaking starts, and what is in the drum at the time, narrow the cause down before any panel comes off.

What the shaking usually means
What you noticeUsual cause
A new or just-moved front loader shakes hard on its first spinsShipping bolts still in place
Shakes with one heavy item, fine with a mixed loadUnbalanced load
The washer rocks when you push down on a corner, even switched offA foot not touching the floor or a loose lock nut
Shakes on every load, worse on a wooden floorThe floor flexes under the washer
Shakes even on a Drain and Spin with the drum emptyA machine fault rather than the load
The tub swings and knocks against the cabinetWorn suspension rods, dampers or springs, or a loose counterweight
A rumble that grows with spin speed and turns into a roarWorn drum bearings

GE suggests the empty-drum test too: run a rinse and spin with nothing in the washer. If it is calm empty and violent full, the load is the problem, not the machine.

Check for Shipping Bolts on a New Front Loader

Front loaders leave the factory with bolts that lock the drum in place for transport. Whirlpool says they must be removed after the washer is installed, and Samsung says a washer with its shipping bolts still in will shake a lot. Samsung’s own check is simple: push the drum with your hand. If it does not move at all, the bolts are probably still in.

GE adds one point about timing: leave the shipping bolts and braces in until the washer has been slid into its final place, then take them out. Keep them, because they are the right way to secure the drum the next time you move house.

Level the Washer and Lock the Feet

A washer that is not level turns every spin into a rocking motion. Whirlpool’s method is to make sure all four feet are firmly on the floor, rock the machine front to back and side to side, and turn the feet until it is stable and no longer rocks. Most adjustable feet have a lock nut, and it needs to be tightened up against the cabinet once the height is right, or the foot slowly unwinds.

GE makes a point most people miss: the further the legs are extended, the shakier the washer gets, especially in the spin cycle. Level it with the legs as short as the floor allows. If the washer sits on a pedestal or a riser, Samsung says the pedestal has to be level first.

Spread the Load

Whirlpool lists uneven loads among the main causes and recommends placing heavier items around lighter ones and not packing the drum tightly. A single bath mat, one pair of jeans on its own or a duvet that has rolled into a ball soaks up water on one side, and the drum cannot balance it. GE’s advice when it happens is to pause the washer, open it and spread the clothes by hand.

Modern washers sense an unbalanced load and try to fix it themselves: they slow down, redistribute and try again, sometimes several times. A cycle that runs long because of that is the machine protecting itself, not a fault. If yours gives up and stops instead, our guide to a washer that will not spin covers what happens next.

Check the Floor Under the Washer

Whirlpool warns that a floor that is uneven or not sturdy enough may not support the washer properly, and Samsung adds that a slippery floor can upset its balance and that carpet and other soft surfaces cause vibration too. Samsung also recommends about an inch of clearance from the dryer and the walls.

A springy timber floor lets even a perfectly level washer bounce. A sheet of plywood under the feet or an anti-vibration mat often fixes that better than any part, and the balancing steps in the washer drum explained go through it in the same order.

When Every Check Passes: Suspension, Counterweights and Bearings

If the washer is level, the floor is solid, the load is spread and it still shakes or bangs, the parts that hold the drum steady are next. The tub hangs on suspension rods, springs or dampers that let it move without hitting the cabinet, and heavy concrete or plastic counterweights keep it steady. When the damping wears out, the tub swings and the machine walks. When a counterweight bolt loosens, the washer bangs on spin.

In our experience a washer that bangs on spin is far more often loose counterweights or spent suspension than a failed bearing, and those are very different bills. Bearings announce themselves differently: a rumble that rises with spin speed and grows into a roar. GE also notes that a clogged drain pump can make a washer shake or vibrate, so a slow drain is worth mentioning when you book.

Is a Shaking Washer Dangerous?

A washer that bangs hard, walks into a wall or knocks its tub against the cabinet should be stopped until it is checked. Running it that way wears the suspension faster and can damage the seal and bearings, which turns a modest repair into a major one.

There is also a recall worth knowing about. In November 2016 the US Consumer Product Safety Commission announced a recall of about 2.8 million Samsung top-load washers, 34 models sold from March 2011 to November 2016, because the top could detach from the chassis during use. CPSC listed 733 reports of excessive vibration or the top detaching. If you own a Samsung top loader from those years, check its model number against the recall notice.

What It Costs When the Machine Is at Fault

Most shaking is fixed without parts: bolts out, feet leveled, load spread. When it is the machine, the bill depends on which part. In Neighborville’s book, across 159 completed washer repairs, the median is $352 and the middle half runs $257 to $416. Balancing work and a loose counterweight sit in the cheapest quarter, under $257, while bearing work sits in the top tenth, above $519. The full picture is in our washer repair cost guide, and for an older machine, how long washing machines last helps with the repair-or-replace decision.

Frequently Asked Questions

Why is my washer shaking violently on spin?
Most often the load is unbalanced, the washer is not level, or on a new front loader the shipping bolts are still in. If all three are fine, worn suspension, a loose counterweight or worn drum bearings are the usual causes.
Is it normal for a washing machine to shake?
A little. GE says movement of up to a quarter of an inch can be normal now and then, because the washer is designed to move rather than pass every force into the floor. Banging, walking or hitting the wall is not normal.
Why does my new washer shake so much?
On a new front loader, check the shipping bolts first. Whirlpool says they must be removed after installation, and Samsung says a washer with them still in will shake a lot.
How do I stop my washer from walking?
Level it with all four feet firmly on the floor, keep the legs as short as possible, tighten the lock nuts and spread the load. If it still walks on a level, solid floor, the suspension is the next suspect.
Can the floor make a washer shake?
Yes. Whirlpool says an uneven floor or one that is not sturdy enough may not support the washer properly, and Samsung warns about slippery floors and carpet. A sheet of plywood or an anti-vibration mat often helps.
Is it worth fixing a washer that shakes?
Usually. Balancing work, suspension and counterweights are among the cheaper washer repairs. Worn drum bearings are the expensive case, and on an older machine they can make replacement the better choice.
Can I keep using a washer that shakes violently?
Stop using it until the cause is found. Heavy shaking wears the suspension and can damage the seal and the bearings, which turns a small repair into a large one.

Sources: Whirlpool Product Help, Washer is Vibrating, Walking or Moving; GE Appliances support, Front Load Washer: Walking, Vibrating, Shaking, or Moving; Samsung US support, Samsung washing machine is shaking too much; US Consumer Product Safety Commission, Samsung Recalls Top-Load Washing Machines, recall 17-028, November 4, 2016; Neighborville field data, 159 completed washer repairs, February 2024 to September 2026.

Last updated: November 2026.

Washer still shaking?

Our technician checks the leveling, the suspension and the counterweights before anyone talks about bearings, so you pay for the part that is actually worn. The $99 diagnostic is applied to the repair when you approve it.

Book online Call us