Bosch Dishwasher Will Not Drain: Filter, Pump Cover and Error Codes

Filters, then the pump cover E:61-02, E:61-03, E:92-40 Drain hose at least 33 inches up Median dishwasher repair $308

Quick Answer: Bosch Dishwasher Not Draining

A Bosch dishwasher that will not drain is usually blocked at the filters or at the drain pump cover, and Bosch tells owners how to clear both. The rest of the list is installation: the disposal plug, a kinked hose or a missing high loop.

  • Filters: a three-part system, micro, fine and coarse, that Bosch says to check after each cycle
  • Drain pump cover: pried off with a spoon to reach the impeller, where glass and debris collect
  • E:61-03: disposal still plugged, hose kinked, pump cover loose or high loop missing, each marked by Bosch as not an appliance error
  • Cancel and drain: press Reset 4 sec. for about 4 seconds and the residual water is pumped out
  • Median dishwasher repair in Neighborville’s own book: $308, middle half $254 to $375

Bosch is unusually direct with owners about drain faults. Its manuals mark most of the drain codes as “not an appliance error”, and they walk you through the same filter and pump cover steps a technician would start with. This page puts those steps in order, explains what each code and light pattern means, and tells you where the owner’s part ends and the repair begins.

Bosch still holding water?

If the filters and the pump cover are clean and it still will not drain, tell us the model number and the code on the display. The $99 diagnostic is applied to the repair when you approve it.

What Bosch Says Causes Water Left in the Machine

Bosch’s Use and Care manuals have a troubleshooting row worded “Water is left in the appliance at the end of the program.” It gives two causes, in this order: the filter system or the area under the filters is blocked, for which Bosch says to clean the filters and then the drain pump; and the program has not yet ended, for which the answer is to wait for it to finish or terminate it with Reset.

The manual separates that from a different complaint that often gets confused with it. An interior that is still wet after the wash cycle is, in Bosch’s words, not an error: condensation drying leaves droplets on the inside walls, which run off and are pumped out. So a damp tub with beads of water is normal. A pool of water across the bottom when the program has finished is not.

Bosch drain causes, as worded in the manuals, and who fixes them
CauseHow it showsYourself?
Filters soiled or blockedWater left at the end; E:92-40 on models with a code displayYes
Drain pump cover loose, or a foreign object in the pumpE:61-02, or E:61-03Yes, with care
Garbage disposal still pluggedE:61-03, usually on a new install or new disposalYes
Drain hose kinkedE:61-03Yes
High loop missing, debris flushed back into the hoseE:61-03Yes, to fit the loop; a blocked hose may need a technician
Program not yet endedWater in the tub mid-programWait, or cancel with Reset
Drain pump failedPump area clean, cover seated, still will not drainNo

Step 1: Clean the Bosch Filter System

Bosch’s filter system has three parts, labelled in the manual as the micro filter, the fine filter and the coarse filter, and Bosch says debris in the rinsing water can block them. Its instruction is to check the filters for residue after each cycle. To clean them, Bosch’s sequence is:

  • Turn the coarse filter counterclockwise and lift out the filter system, making sure nothing falls into the sump
  • Pull the micro filter downward and off
  • Press the locking catches together and take the coarse filter upward and out
  • Clean the parts under running water, and carefully remove the rim of debris between the coarse and fine filters
  • Put the system back together so the coarse filter’s catches click into position, insert it, and turn the coarse filter clockwise until the arrow markings line up

On models with a code display, E:92-40 lighting up is Bosch telling you exactly this: the filters are soiled or blocked.

Step 2: Clear the Drain Pump Under the Pump Cover

If clean filters do not fix it, Bosch’s next instruction is to clean the drain pump, because large food remnants or foreign objects can block it. Bosch puts this in the owner’s manual, with a caution that matters: there may be sharp debris, such as glass fragments, blocking the pump, so take care when removing parts.

  • Disconnect the dishwasher from the power supply
  • Remove the upper and lower racks, then the filter system
  • Scoop out the water, using a sponge if necessary
  • Pry the pump cover off using a spoon, grip it by the crosspiece, lift it diagonally inward and take it out
  • Reach the impeller by hand and remove any food remnants or foreign objects around it
  • Insert the pump cover and press down until it clicks into position, then refit the filters and the racks

That click matters. Bosch’s E:61-02 describes a drain pump cover that is loose as well as a blocked pump, so a cover that was not pressed fully home after cleaning brings the same code straight back. If the impeller turns freely, the cover is seated and the machine still will not pump, the pump itself is the suspect, and that is a repair rather than a cleaning job. The pump side of it is covered in the dishwasher drain pump.

Bosch Drain Error Codes: E:61-02, E:61-03 and E:92-40

On Bosch models with a code display, the drain codes in the current manuals are these, and Bosch marks most of them as not an appliance error:

Bosch drain codes, as described in Bosch Use and Care manuals
CodeBosch’s descriptionWhat to do
E:92-40Filters are soiled or blockedClean the filters
E:61-02Drain pump cover loose, or a foreign object blocking the pumpClean the drain pump and press the cover until it clicks
E:61-03Water is not draining: disposal still plugged or hose kinked; pump cover loose or pump blocked; high loop missing or debris flushed back into the hoseCheck all three, in that order

Some manuals print the second code as E:6103 rather than E:61-03; it is the same code. On models without a code display, such as the SHP65CC5UC, Bosch uses a light pattern instead: four vertical LEDs, the cycle duration indicators and the clean indicator, lighting up at the same time. Bosch lists the same drain causes for that pattern, and also two inlet causes, a kinked inlet hose and a closed water supply valve, so check both directions.

How to Drain a Bosch Dishwasher and Cancel the Cycle

If you need the water out now, cancel the program and let the machine pump. Bosch’s manuals give the same button for this across many models: press Reset 4 sec. for approximately 4 seconds. All the displays light up, the residual water is pumped out, and the cycle is cancelled and ends after about a minute.

Button layouts differ between Bosch series, and on some models the steps around the door are different, so use the sequence in your own manual if the display does not respond.

If cancelling does not move the water, the pump is not able to, and bailing it out by hand is the only way. Switch the machine off at the power supply, scoop the water out with a cup and finish with a sponge, then go to the filters and the pump cover above. The general method is in dishwasher not draining.

The Drain Hose, High Loop and Disposal Plug

Three of the causes behind E:61-03 are installation, not the dishwasher, and Bosch’s installation instructions are specific about all three.

  • Height. A portion of the drain hose must be at least 33 inches off the floor, otherwise the dishwasher may not drain properly. The same document says not to exceed 43 inches in drain hose height
  • High loop or air gap. The drain hose must be installed with one or the other. Without it, Bosch’s own troubleshooting notes that debris can flush back into the drain hose and block it
  • The disposal plug. If the hose connects to a garbage disposal, the plug in the disposal’s dishwasher connection must be removed first. A new dishwasher or a new disposal that has never drained is the classic case
  • Length. The maximum drain hose length, including the hose to an air gap, is 150 inches

Routing and checking the hose in detail is in the dishwasher drain hose. If the kitchen sink beside the dishwasher also drains slowly, the problem is the household drain line, and no work on the dishwasher will fix it.

Bosch Warranty: Check Before Booking

The Bosch Statement of Limited Product Warranty in the manuals we checked covers defects in materials and workmanship for 365 days from the date of original delivery. It adds longer limited cover on certain parts, which excludes labor charges: five years on the microprocessor and printed circuit boards, five years on the dish racks, and a lifetime warranty against stainless steel rust through. Installation problems are excluded, and the manual separately notes that damage caused by freezing is not covered.

So in practice: inside the first year, a drain fault that is a genuine defect is Bosch’s to fix, and the number in the manual is 1-800-944-2904. Most drain calls are not defects, though: a blocked filter, a pump cover or a disposal plug is something Bosch itself calls not an appliance error. Bosch also states that genuine spare parts are available for up to 15 years from the date a model was placed on the market.

Bosch Dishwasher Drain Repair Cost

These are our own completed jobs, counted as jobs billed above the diagnostic fee with sales tax on it, across all dishwasher makes.

Dishwasher repair cost, Neighborville completed jobs, February 2024 to September 2026
MeasureFigureBase
Median dishwasher repair$30864 completed dishwasher repairs
Middle half$254 to $375the 25th to 75th percentile
Filter or pump cover cleared by the owner$0the steps Bosch gives in the manual
Diagnostic visit$99flat, applied to the repair on approval

The figures cover every dishwasher make we repaired, not Bosch alone, because we do not publish a median from fewer than twenty repairs. The full appliance-by-appliance picture is in real appliance repair cost data, and Bosch service in general is on the Bosch appliance repair page.

What a Proper Diagnosis Checks

The code or light pattern read and recorded; the program confirmed ended rather than interrupted; the filter system removed and cleaned; the pump cover removed, the impeller turned by hand and the sump cleared of glass; the cover refitted until it clicks; the drain hose checked for kinks, for its 33-inch rise and for debris flushed back into it; the disposal connection checked for its plug; the sink drain checked so a household blockage is not blamed on the machine; and only then the drain pump tested electrically. You get the fault named, the part named and the total before anything is ordered. Dishwasher work in general is on the dishwasher repair page.

GE handles the same fault differently, with a 3-second cancel that drains the tub and its own drain codes: GE dishwasher not draining.

Frequently Asked Questions

Why will my Bosch dishwasher not drain?
Bosch’s own troubleshooting gives two causes for water left in the machine at the end of a program: the filter system or the area under the filters is blocked, or the program has not yet ended. After that, Bosch lists a loose drain pump cover or a foreign object in the pump, a garbage disposal plug that was never removed, a kinked drain hose, and a missing high loop that lets debris flush back into the hose. Clean the filters and the drain pump first, then check the hose and the disposal connection.
How do I drain a Bosch dishwasher?
Cancel the program and let the machine pump out. Bosch’s manuals say to press Reset 4 sec. for approximately 4 seconds; the displays light up, the residual water is pumped out, and the cycle ends after about a minute. The exact button layout differs between series, so follow your own manual. If the water still stays, switch the machine off at the power supply and clean the filters and the drain pump.
How do I clean the drain pump on a Bosch dishwasher?
Bosch’s procedure: disconnect the dishwasher from the power supply, remove the upper and lower racks and the filter system, and scoop out the water, using a sponge if necessary. Pry the pump cover off using a spoon, grip it by the crosspiece, lift it diagonally inward and take it out. You can then reach the impeller by hand and remove food remnants or foreign objects. Press the cover back until it clicks into position. Bosch warns that sharp debris such as glass may be blocking the pump.
What does E:61-03 mean on a Bosch dishwasher?
Bosch’s manuals describe E:61-03 as water not draining, and list three causes, each marked as not an appliance error: the garbage disposal is still plugged or the drain hose is kinked; the drain pump cover is loose or a foreign object is blocking the pump; or the high loop is missing and debris has flushed back into the drain hose and blocked it. E:61-02 is the pump cover or a blocked pump on its own, and E:92-40 means the filters are soiled or blocked.
My Bosch has no code display. How does it show a drain fault?
On models without a code display, such as the SHP65CC5UC, Bosch uses a light pattern instead. Its manual lists four vertical LEDs, the cycle duration indicators and the clean indicator, all lighting up at the same time, with the same causes as the drain codes: a plugged garbage disposal or kinked drain hose, or a loose or blocked drain pump cover. That same pattern can also mean an inlet problem, a kinked inlet hose or a closed water supply valve.
Is water left in a Bosch dishwasher after a cycle normal?
Wet surfaces are. Bosch’s manual says an interior still wet after the wash cycle is not an error, because condensation drying leaves water droplets that run off and are pumped out. Standing water across the bottom at the end of a program is different: Bosch’s troubleshooting treats that as a blocked filter system, a blocked area under the filters, or a program that has not yet ended.
How high should a Bosch drain hose be?
Bosch’s installation instructions say a portion of the drain hose must be at least 33 inches off the floor, otherwise the dishwasher may not drain properly, and that the hose must be installed with either a high loop or an air gap. The same document says not to exceed 43 inches in drain hose height, and that the plug in a garbage disposal’s dishwasher connection must be removed before the hose is connected to it.
How much does Bosch dishwasher drain repair cost?
Across 64 completed dishwasher repairs in Neighborville’s own book, the median finished repair is $308 and the middle half runs $254 to $375. If the fault is a filter or a pump cover, Bosch’s own steps clear it at no cost. The exact price is given after the $99 diagnostic, which comes off the repair when you approve it.

Sources: troubleshooting rows, the filter system, the drain pump cleaning procedure, the E:61-02, E:61-03 and E:92-40 codes, the Reset 4 sec. cancel, the LED pattern and warranty terms are from Bosch dishwasher Use and Care manuals 9001964589 (SHE53B75UC) and 9002072817 (SHP65CC5UC). Drain hose height, high loop, air gap, disposal plug and hose length are from Bosch dishwasher installation instructions 9002059336. Repair figures are Neighborville’s own completed jobs, February 2024 to September 2026, counted as jobs billed above the diagnostic fee with tax, above $108.90: 64 completed dishwasher repairs across all makes. Neighborville is an independent repair company and is not affiliated with Bosch or BSH; brand names are used to identify the appliances we service.

Last updated: November 2026.

Filters and pump cover first, then call.

Bosch’s own steps clear those at no cost. If they do not fix it, the code and the model number tell us what to bring.

Book online Call us