How to Drain a GE Dishwasher, and Why It Will Not Drain

Hold Start 3 seconds to drain 1 to 2 cups can be normal High loop at least 32 inches Median dishwasher repair $308

Quick Answer: How to Drain a GE Dishwasher

Press and hold the Start pad for 3 seconds and close the door. GE’s owner’s manuals say the dishwasher will then drain, beep, and turn the wash cycle light off. If it will not pump out, the cause is usually somewhere GE tells owners to look first.

  • Is it really a fault? On models without an Ultra Fine filter, GE calls 1 to 2 cups of clean water normal
  • Filters and sump: clogged Fine and Ultra Fine filters, or paper and food covering the sump at the rear of the tub
  • Plumbing: a kinked hose, a clogged air gap, a full disposer or a disposer drain plug never removed
  • Codes: C1, C3 and FTD or F56 all point at draining
  • Median dishwasher repair in Neighborville’s own book: $308, middle half $254 to $375

GE’s support pages are clear about where the owner’s part ends: once the filters, the sump, the hose, the air gap and the disposer are clear, GE says service will be needed. This page follows GE’s own order, explains what the codes mean, and tells you how much water in the bottom is actually a problem, because on some GE models a little is by design.

GE still holding water?

If the filters, the air gap and the hose are clear and it still will not drain, tell us the model number and the code. The $99 diagnostic is applied to the repair when you approve it.

How to Drain a GE Dishwasher: Cancel the Cycle

The first way to get water out is to let the dishwasher do it. GE’s owner’s manuals for current built-in models, including the GDT, GDF, GDP and PDT series, give the same instruction: to cancel a wash cycle, press and hold the Start pad for 3 seconds and close the door. The dishwasher will drain, emit a beep, and the wash cycle light will turn off.

GE’s support pages add two variations. On most models, holding the Start or Start/Reset pad for 3 seconds also cancels a Delay Start. On older electronic-control models, GE says to press the Start/Reset pad twice, after which the dishwasher runs about 90 seconds while it pumps out. On mechanical dial models, the timer knob is turned a full revolution clockwise to OFF.

If the dishwasher hums or runs but the water stays, the drain path is blocked, and pressing buttons again will not move it. Switch the machine off, bail the water out with a cup and finish with a sponge so you can see the tub floor and the filters. The general method is in dishwasher not draining.

How Much Water Is Normal in a GE Dishwasher?

Before taking anything apart, check whether there is a fault at all, because GE’s answer depends on the model. On GE models without an Ultra Fine filter, GE says 1 to 2 cups of clean water covering the bottom of the tub is normal. On models with an Ultra Fine filter, water in the sump, the filter area, is normal, but it should not cover the bottom of the tub.

Two more things GE describes as normal. The drain pump starts and stops several times during each drain. And on models with the UltraFresh feature, the dishwasher may add and drain water at intervals, so you may see water in the bottom or hear the drain pump outside a cycle. What GE does not call normal is dirty water that builds up over time, and for that its first answer is the high drain loop.

GE Dishwasher Not Draining: GE’s Own Checklist

GE’s support page for a dishwasher that is not draining lists these checks. Work through them in this order, because the first ones are free and the most common.

What GE tells owners to check when a dishwasher will not drain
CheckWhat GE saysYourself?
Sump areaNo paper or large object covering or blocking the sump at the rear of the tub; clear out large food such as noodles, lettuce or bonesYes
FiltersOn models with Fine and Ultra Fine filters, remove and check themYes
Drain hoseCheck below the sink for a blockage or a kink; re-using an old, worn hose may promote kinkingYes
Sink drain and disposerMake sure the sink drain is not clogged and run the disposer to clear it; never put your hands into the disposerYes
Air gapRemove the cap and clean out any build-up of debrisYes
New disposerMake sure the drain plug inside the disposer was removedYes
DetergentThe wrong type or too much can over-suds and stop the dishwasher draining properlyYes
Pump, check valve or drain lineIf the above does not resolve it, service will be neededNo

The disposer plug deserves its own line. GE’s installation instructions put it in capitals: when connecting the drain line to a disposer, check that the drain plug has been removed, because the dishwasher will not drain if the plug is left in place. A brand-new dishwasher, or a new disposer under an old one, that has never drained properly is the classic case.

Clean the GE Fine and Ultra Fine Filters

Most newer GE dishwashers have Fine and Ultra Fine filters that GE says need routine maintenance. Some older and some current models have self-cleaning filtration instead, with usually no removable filter to clean, so check your model first. Where the filters are removable, GE’s steps are:

  • Remove the bottom rack
  • Twist the Ultra Fine filter counterclockwise and lift it out
  • Rinse it with warm soapy water and a sponge; GE warns that scouring pads or brushes can damage it
  • Remove the Fine filter, the mesh plate beneath it, from under its rear retaining tabs or posts
  • Refit both, twisting the Ultra Fine filter clockwise to lock it, using the arrow on the Fine filter as a guide

GE’s current manuals say to do this every other month or more depending on use, and that gritty dishes or a drop in wash performance are a sign it is due. On the GDT225 and PDT145 series the assembly is different, with a coarse filter, a fine filter and a filter plate, and that manual says to check them every month or more and to make sure nothing has fallen into the opening in the bottom before refitting.

The Air Gap, High Loop and Drain Hose

GE is explicit that an air gap is not part of the dishwasher: it is part of the plumbing, usually a chrome cylinder on the back of the sink beside the faucet, and its manuals note it is not covered by the dishwasher warranty. To clean it, GE says to remove the chrome cover, unscrew the plastic cap, remove any build-up, rinse the cap, and check the hose from the air gap to the sink drain or disposer is not clogged.

Where there is no air gap, the hose needs a high drain loop instead. GE’s figures:

  • High drain loop: a minimum of 32 inches above the floor, attached to the underside of the countertop. Without it or an air gap, GE says dirty water from the sink can flow into the dishwasher
  • Air gap required if local codes demand one, or if the waste tee or disposer connection is less than 18 inches above the floor
  • Maximum height: the drain connection should not be more than 72 inches above the bottom of the dishwasher
  • Maximum length: total drain hose length must not exceed 12 feet

GE also builds an anti-backflow valve, which it calls a check valve, into the pump housing to stop soiled drain water flowing back in, but it is clear that the dishwasher still needs the high drain loop. Hose routing in more detail is in the dishwasher drain hose.

GE Dishwasher Drain Codes: C1, C3 and FTD

GE’s code list notes that not all codes are found on all models. The ones that relate to draining are:

GE dishwasher drain-related codes, from GE’s support page
CodeGE’s descriptionGE’s fix
C1The pump out during drain has exceeded 2 minutesClean the air gap, replace or reposition the hose, run the disposer; contact service if it persists
C2The total pump out cycle exceeds 7 minutesPress RESET to stop the beep
C3The dishwasher will not drainDisconnect power at the breaker for about 30 seconds, then reset; contact service if it persists
C4Filled twice after a power failure; float switch stuck or failed; clogged drain or sumpTouch Start then cancel; tap the float cover to free the float; check the sump for debris
FTD or F56Failure to drainCheck the drain hose, air gap and disposer

GE adds that disconnecting power to the dishwasher for a minute or two sometimes clears a code, and that if this simple reset does not, service may be required. A code that returns after the hose, air gap and disposer are clear is the point to book.

What Not to Do

  • Do not use drain cleaner. GE says chemical drain cleaners should never be used in a dishwasher for any reason, because they can damage the rubber parts
  • Do not put your hands into the disposer to check it. Run it instead
  • Do not plumb other devices into the dishwasher drain hose, which GE lists separately
  • Do not reuse an old drain hose on a new machine. GE says new dishwashers come with a white corrugated hose that should be used

GE Warranty: Check Before Booking

The GE dishwasher owner’s manuals we checked carry a one-year limited warranty from the date of original purchase, during which GE Appliances covers any part that fails from a defect in materials or workmanship, with labor and related service free of charge. The same page excludes improper installation or maintenance, products working as described in the owner’s manual, resetting circuit breakers, and cleaning or servicing the air gap. So inside the first year, a failed pump is GE’s to fix; a clogged filter, air gap or disposer plug is not a defect under those terms.

GE Dishwasher Drain Repair Cost

These are our own completed jobs, counted as jobs billed above the diagnostic fee with sales tax on it.

Repair cost, Neighborville completed jobs, February 2024 to September 2026
MeasureFigureBase
Median dishwasher repair, all makes$30864 completed dishwasher repairs
Middle half$254 to $375the 25th to 75th percentile
GE median bill, all appliance types$358GE repairs where the brand was logged
Filter, air gap or disposer plug cleared yourself$0the checks GE gives owners
Diagnostic visit$99flat, applied to the repair on approval

The pump side of the repair is covered in the dishwasher drain pump, and dishwasher work in general on the dishwasher repair page.

What a Proper Diagnosis Checks

The code read and recorded; the cycle cancelled to see whether the pump runs at all; the water level judged against GE’s normal for that model; the filters and the sump cleared; the drain hose checked for kinks and for its 32-inch loop; the air gap and the disposer connection cleared, including the disposer plug; the sink drain checked so a household blockage is not blamed on the machine; the float checked for sticking; and only then the drain pump and the check valve in the pump housing tested. You get the fault named, the part named and the total before anything is ordered.

Frequently Asked Questions

How do I drain a GE dishwasher?
Cancel the cycle and let it pump out. GE’s owner’s manuals say to press and hold the Start pad for 3 seconds and close the door; the dishwasher will drain, beep, and the wash cycle light will turn off. On older electronic models GE says to press Start/Reset twice, after which the dishwasher runs about 90 seconds while it pumps out. If the water still does not go, switch it off, bail it out by hand, and check the filters, the air gap and the drain hose.
Why is my GE dishwasher not draining?
GE’s own checklist, in order: debris or paper covering the sump area at the rear of the tub; clogged Fine and Ultra Fine filters on models that have them; a kinked or blocked drain hose under the sink; a clogged kitchen sink drain or disposer; a clogged air gap; a drain plug left inside a newly installed disposer; and over-sudsing from the wrong detergent or too much of it. If none of those fixes it, GE says service will be needed.
How much water in the bottom of a GE dishwasher is normal?
It depends on the filter. GE says that on models without an Ultra Fine filter, 1 to 2 cups of clean water covering the bottom of the tub is normal. On models with an Ultra Fine filter, water in the sump, the filter area, is normal, but it should not cover the bottom of the tub. Dirty water that builds up over time is not normal, and GE points first at a missing high drain loop.
What does C1 or C3 mean on a GE dishwasher?
On GE’s code list, C1 means the pump out during drain has exceeded 2 minutes; GE’s fix is to clean the air gap, replace or reposition the hose, run the disposer, and contact service if it persists. C3 means the dishwasher will not drain; GE says to disconnect power at the circuit breaker for about 30 seconds, then reset the dishwasher, and contact service if it comes back. FTD or F56 means failure to drain, and GE says to check the drain hose, air gap and disposer. Not all codes are found on all models.
How do I clean the filter on a GE dishwasher?
On models with removable filters, GE’s steps are: remove the bottom rack, twist the Ultra Fine filter counterclockwise and lift it out, and rinse it with warm soapy water and a sponge, because scouring pads or brushes can damage it. Then remove the Fine filter, the mesh plate under it. Twist the Ultra Fine filter clockwise to lock it back in, using the arrow on the Fine filter as a guide. GE’s current manuals say to do this every other month or more depending on use. Some older and current GE models have self-cleaning filtration with no removable filter.
How high should the GE dishwasher drain loop be?
If there is no air gap, GE says the drain hose must have a high drain loop at a minimum of 32 inches above the floor, attached to the underside of the countertop. GE’s installation instructions add that the drain connection should not be more than 72 inches above the bottom of the dishwasher, that the total drain hose length must not exceed 12 feet, and that an air gap must be used if the waste tee or disposer connection is less than 18 inches above the floor.
Can I use drain cleaner in a GE dishwasher?
No. GE says chemical drain cleaners should never be used in a dishwasher for any reason, because they can damage the rubber parts. If the dishwasher will not drain after the filters, sump, hose and air gap are clear, GE describes the remaining possibilities as a clog in the sump area, the pump or the drain line, which is a service job.
How much does GE dishwasher drain repair cost?
Across 64 completed dishwasher repairs in Neighborville’s own book, the median finished repair is $308 and the middle half runs $254 to $375. Our median GE bill across all appliance types is $358. A clogged filter, air gap or disposer plug costs nothing to clear yourself; the exact price for a pump or valve repair is given after the $99 diagnostic, which comes off the repair when you approve it.

Sources: the cancel and drain steps, filters, normal water levels, the not-draining checklist, drain codes, air gap cleaning, the anti-backflow valve, the drain cleaner warning and normal pump behaviour are from GE Appliances’ dishwasher support pages and GE dishwasher owner’s manuals 49-4000283, 49-4000214, 49-55122 and 49-55124. High loop, air gap, hose height and length limits and the disposer plug are from GE built-in dishwasher installation instructions 31-31560. Repair figures are Neighborville’s own completed jobs, February 2024 to September 2026, counted as jobs billed above the diagnostic fee with tax, above $108.90: 64 completed dishwasher repairs across all makes. Neighborville is an independent repair company and is not affiliated with GE Appliances or Haier; brand names are used to identify the appliances we service.

Last updated: November 2026.

Hold Start, check the air gap, then call.

If cancelling does not pump it out and the filters, hose and air gap are clear, the code and the model number tell us what to bring.

Book online Call us